How to Clean Venetian Blinds

Venetian blinds can be dust collectors and depending on their location, can be a magnet for dirt and grime. Regular maintenance and cleaning is important.

You Can Clean Them Outside

What you will need:

  • Large blankets (to lay your blinds on)
  • Bucket
  • Cleaning liquid (the type of cleaner you use  should be dependent on the material your blinds are made of)
  • Hose
  • Soft scrub brush or Sponge mop
  • Old towels

Instructions:

  1. Remove the blinds from the window, leaving the hardware in place. Assemblies for Venetian blinds vary, and you may need a      screwdriver for this step. CAUTION: It is always recommended that you have a helper, especially if you need to use a step stool or ladder.
  2. Take the blinds (one at a time) outside and place on top of one of the blankets or tarps, making sure they are fully  extended, slats closed.
  3. Mix cleaning liquid with water in the bucket  (typically 1 part cleaner to 4 parts water for non-fabric blinds). TIP:   Car wash liquid or vinyl cleaning products work best, especially if you  have stuck-on dirt or grease, but liquid dish soap will work well also.
  4. Pour the bucket of soapy liquid over the blinds, being sure to wet all slats.
  5. Using the soft scrub brush or sponge mop, scrub the slats thoroughly.
  6. Turn the blinds over, and repeat procedure on the other side.
  7. Hose off all soapy residue. TIP: Hose off both  sides thoroughly—if soap dries on the slats, it will attract excess dirt and grime.
  8. Mop up excess water from the blinds with the towels.
  9. Bring blinds indoors and lay flat (on towel)  to dry completely before re-hanging.

Or You Can Clean Them Inside

What you will need:

  • Bathtub
  • Cleaning liquid (they type of cleaner you use should be dependent on the material your blinds are made of)
  • Soft scrub brush
  • Old towels

Instructions:

  1. Fill tub with warm soapy water.
  2. Remove the blinds from the window, leaving the hardware intact. Assemblies for Venetian blinds vary, and you may need a screwdriver for this step. CAUTION: It is always recommended that you have a helper, especially if you need to use a step stool or ladder to reach the top of the blinds for removal.

Take the blinds (one at a time) and place in the tub, fully extended, slats closed. TIP: Depending on the size of your blinds, it may be necessary to fold them over.

  1. Let soak for 15 minutes.
  2. Using the soft scrub brush, scrub each slat to  remove dirt and grime.
  3. Flip the blinds, and scrub again.
  4. Drain the dirty water.
  5. Turn on the shower and rinse the blinds (both sides). TIP: A hand-held shower nozzle is quite handy for this step.
  6. Place the blinds on their side (leaning against the edge of the tub) and let the water drain.
  7. After about 20 minutes, place on the opposite  side to avoid pooling of excess water in the crevices, let air dry for  another 20 minutes. TIP: If you’re short on time, use a hair dryer set at  its lowest temperature to help speed up the drying process.  strong>CAUTION: Do not hold the hair dryer too close to the slats, or  use it on a high temperature, or you may damage the slats.
  8. Towel off any remaining water, and re-hang.

Maintenance Cleanings

Regular maintenance will cut down on the frequency of deep cleaning.

  1. Extend your blinds all the way.
  2. Tilt the slats up (or to one side if they are vertical) and dust lightly with a cloth or duster.
  3. Tilt the slats down (or to the opposite side  if they are vertical) and dust the other side lightly with a cloth or  duster.
  4. As an alternative, try using a soft cloth  glove. Hold each slat between your thumb and forefinger; gently run them along each slat. To avoid damage, don’t exert too much pressure or crimp the slats.
  5. A vacuum cleaner may also be used. Place the  soft brush attachment on the hose and run very lightly over the slats  first in their up position then in their down position. You should first test a small area of the blinds to make sure the suction is not too great.    Some vacuums may damage the slats.
  6. For individual stains on any given slat, spray  with window cleaner, wait 1 to 2 minutes, and wipe with a soft cloth. If  your blinds are cloth, test this on a hidden area first.

A Cleaning Trick(et)

To save time and energy, try using a “tricket.” A tricket is a tool that looks like a multi-pronged squeegee. One type has sponges on both sides, one type has squeegees on both sides, and they clean both sides of the slats without taking the blinds down. They are not perfect but they can save you a lot of hassle and can be purchased at most janitorial supply stores.

Additional Tips

Once you’re blinds are cleaned rub each slat with a dryer sheet. This will help cut down on the amount of dust and grime that accumulates.

It is always best to use cleaning products and detergents that are natural and gentle to the environment. With today’s increased awareness such products are easier to find..

 

Share & Like! Facebook Twitter Google Digg Reddit LinkedIn Pinterest Email